Bearings do not normally click, but i have seen it before. I pulled the wheel off and put the car in drive and listen for the noise.
If the cv joint is noisy, it needs to be replaced.
Cv axle making clicking noise. Most times it is the outer, (closest to the wheel) since that is the one that gets most of the action. Without this grease, the components are dry, resulting in a clicking sound. When cv axles become excessively worn, the constant velocity joints will become loose and click when turning or accelerating.
My car has suffered from the well documented clicking noise (from drivers side) rear axle since purchase. A car has 4 cv joints. A common source of clicking noise comes from a gear broken tooth.
This is the point where the front and rear axels join with the tires. The brake pads look fine, good thickness, no glazing. A flexible rubber boot, filled with axle grease, covers each connection.
When they do wear out, the cv axles will usually show symptoms to let the driver know they require attention. Loud clicking noises when turning or accelerating. Usually they make a clicking sound when turning left or right but, if the socket is really dry and consequently, worn, then it could make a noise.
But the same clicking sound during acceleration or deceleration may also point to an issue with the drive chain in the transfer case. So for the past two weeks while driving to work, which is a very steep grade road with a lot of switchbacks, my subaru forester starting making a clicking sound when turning left. Clicking in the drivetrain can only be a handfulof things, if its not motor related (it would do it when engine rev's, even out of gear) then it is cv joints, a nail in tire or a bad wheel bearing.
If a clunking noise is heard while speeding up or slowing down, it can mean damage to the inner and outer cv joints. Once the joint makes noise, you cannot add grease to the damaged joint and make the noise go away. A clunking sound, during this phase of testing, can indicate either an inner or outer cv joint failure;
One of the most common and noticeable symptoms of a bad or failing cv axle shaft assembly is an audible clicking noise when turning or accelerating. A popping or clicking noise when turning is a classic symptom of a bad outer cv joint. When a car makes a clicking noise from the front of the vehicle while turning and accelerating, the cause is damage to the cv joint.
This accompanied by a lack of lubrication is another cause of the ‘clicking’ or ‘clucking’ noise you hear when the cv is dry and worn out. The most common symptom of a bad cv axle is a clicking noise when turning. Just low speed braking (coming to a stop, clicking starts around 20 mph).
If any boot gets torn and leaks grease, it has to be replaced. The cv joint allows flexibility in each end of the axle shaft as the vehicle is going down the road. I immediately thought it was my cv joints and took it in today.
The noise is either coming from the cv axle or the wheel bearing. • a “whirring” noise while decelerating at any or all speeds is most likely caused by bad pinion bearings or loose pinion bearing preload. Symptoms of a bad cv axle shaft.
And to my knowledge the only thing that could cause the clicking on a hard turn under acceleration is a defective outer cv joint. A third way a cv joint can fail is when the rubber boot becomes old and brittle due to age and wear. Continuous knocking, while driving at low speeds, may also be due to joint damage.
It could be a cv joint problem, but the clicking is quite different than the one i can find on youtube. When only on a slope, turning to the right at a very low speed or stationary (tight turn in my garage). The damaged cv joint needs replacing.
Here are a few other sounds and symptoms of bad wheel hub bearings: (it is possible of course that various different problems exist). The noise is on driver side 100%.
The cv axle shaft boot is probably torn, which then leaks grease. The sound is loudest on the of the vehicle with the faulty axle, which makes it easy to determine which axle is causing the problem. The mechanic looked under the car and informed me that none of the boots are damaged and the axels are secure.
This is sometimes also caused by a damaged cv joint, but can also be due to worn wheel bearings if you hear a clicking noise when turning. This clicking noise when you turn is most likely coming from your cv axle. If the boot is torn or leaking, it should be replaced regardless of the condition of the joint.
It is possible to clean the debris out of the cv joint and repack it with new grease to slow the joint's destruction, but the noise will never go away, and eventually, you will need to replace the cv joint. If the clicking is heard during acceeration on a straight line it is usually the inboard joint. This clicking noise is caused by a loose cv joint in a worn down axle.
A failed cv joint is going to make a clicking noise when turning. If you listen closely, you may be able to tell which side it's coming from. One of the most common and most noticeable symptoms of a bad or failing cv axle shaft assembly is an audible clicking noise when turning.
Typically this indicates an issue with the outer cv joint, and the sound is the loudest on the joint that’s opposite of the turning direction. If it is a humming or whining noise it is most likely a wheel bearing. A clicking noise while turning in a front wheel drive car is usually caused by damaged or worn cv joints.
I think the first symptom of a damaged cv joint can indeed be a clicking noise, usually when making a low speed turn, especially on acceleration; Here are my issues and why i think its mainly the cv axle. Cv noise is usually more of a clicking or light knocking sound worn cv joints are usually evident when the steering wheel is in full left hand or right hand locks.
If you do not hear a clicking noise on turns then it is not a cv joint. A damaged axle shaft makes itself vibrate harshly because its balance is already affected. Aside from the clicking noise, too much vibration while driving can be a symptom for a malfunctioning cv joint.
In addition to humming, a defective cv axle can develop any number of clicks, pops and clunks as the damage to the axle joints worsens. When cv axles become excessively worn, the joints will. During rotation of an unbalanced shaft, the whole car starts to vibrate.
Cv axle boot on that side is torn and leaking, just started not a lot of grease all. Another damaged cv joint symptom. Also note the condition of the cv joint boot.
The 535 ix have either tripod constant velocity joint under the boot. It is possible that he hammered the hub over the axle damaging the balls on the outboard joint. But there are times when a noise coming from under the car can be a serious matter.
Here are a few common “noises” that may come from the rear axle that need immediate attention: Listen to the advice you were given. If you hear a clicking, clunking or popping noise from the front wheels, particularly while turning, it means the situation has progressed to the point where the cv joint is damaged.
Its there the hub meets. If it doesn’t, you may have a bad wheel bearing. The noise is fairly loud, especially when the car is making a sharp or fast turn.
You can drive on a damaged cv joint for a little while, but there’s no telling how long “safe” operation will last. This sounds like a wheel bearing. The main culprit is the axle.
A bad cv joint will exhibit a clunking noise as the transmission engages. After about 20 minutes of driving i can hear a loud clicking noise when applying the brakes at low speeds. Clicking noise from front axle while turning.
Here is how to check. This is most often heard during sharp turns at lower speeds. Cv joints are mounted on each end of a front axle, they transfer power to the wheels from the transmission.
(rear end) it isn't cv + axle related, as i don't hear clicking noises making sharp turns and so forth.